MXR M81 Bass Preamp Pedal

3.075,-

Bass Preamp kombinerer en ren bass- preamp med en Direct Out i studiokvalitet. Seperate kontrollere for å justere inn-/utnivå og 3-bånds EQ med trinnløst mellomregister.

MXR M135 Smart Gate Pedal

2.550,-

En uslåelig gate utstyrt med tre typer av støyreduksjon, ”hiss”, ”mid” og ”full”. Et must for alle med en svakhet for high-gain forsterkere eller et overfylt pedalbrett. Smart Gate® Noise Gate M135 Transparent noise suppression Three-point filter cut-off Gates out noise slowly when notes are being held and quickly when they are stopped short Tame your hissing high-gain amp or silence your string of stompboxes with this ingenious pedal. The Smart Gate is equipped with three selectable types of noise reduction to handle virtually any type of signal. It bites down on sizzle and hum but lets the smallest detail of your playing through. With its uncanny ability to sense precisely when—and how fast—to engage, this little genius will never get in your way, so you can wring every last bit of sustain out of that chord without being cut off. The M135 features a hardwire bypass, precise threshold trigger, and amazingly clean circuitry. Power: Dunlop ECB003 AC Adapter or Single 9 volt battery Save

MXR M195 Noise Clamp Pedal

2.050,-

Still dine effektpedaler til ekstreme nivåer uten å tenke på unødvendig bråk og ulyder med MXR Noise Clamp. Gjennom å analysere rålyden fra gitaren kan Noise Clamp redusere alt støy og ulyder fra alle effektpedalene når du ikke spiller. En enkel kontroller gir deg mulighet til å sette terskelen for når effekten går igang. Perfekt demping for de øyeblikkene mellom sanger, helt uten at det påvirker lyden når du ønsker å spille! Noise Clamp M195 Eliminates hiss & excess noise from your effects chain Single threshold Trigger knob Reduces noise up to 26 dB, maintaining riff definition at extreme gain levels Crank your stomp pedals to the extremes without the fear of any hiss or excess noise with the MXR Noise Clamp. By sensing your guitar's dry signal, The Noise Clamp reduces the noise level within the effect loop, coming down hard on even the noisiest signals. A single Trigger knob allows you to set the volume threshold at which the pedal is active, and a green LED shows whether the gate is on/off. This bad boy is capable of reducing Noise up to 26dB, maintaining riff definition at extreme gain levels.

MXR MC401 Boost/Line Driver ...

2.050,-

Boost/Line Driver er en ultraren boost for solospill eller drive-effekter, som enkelt også løser signalulikheter som kan oppkomme når flere pedaler kombineres. MC401 Boost/Line Driver MC401 Simple in design but superbly effective in solving a variety of mismatched line level and signal conditioning problems Used for years in the world's best guitarist's rigs to remedy level problems The MC401 is simple in design but superbly effective in solving a variety of mismatched line level and signal conditioning problems that can occur when combining effects. The MC401's circuit design has been used for years by CAE in the world's best guitarist's rigs to remedy these problems and rejuvenate the sparkle, punch and brilliance that can be lost. It can also be used as an ultra-clean boost (up to +20dB) for solos or to drive effects for more dynamics and sensitivity. Power: Single 9 volt battery, ECB003 AC Adapter or ECB004 AC Adapter for 18 volt operation (for increased headroom)

MXR MC406 CAE Buffer

1.695,-

Når du har en hel kjede med effektpedaler som har forskjellige impedanser, er det umulig å unngå signalforstyrelser. MC-406 Buffer, retter disse signalproblemene. Den ”gainer” signalet opp til +6dB, den har HI/LO-cut bryter, og en ekstrautgang for f.eks stemmemaskin. When you run your signal from your instrument to your amp though long cables and/or through a large array of effects with varying impedance, there's bound to be some signal degradation. Placing the CAE Buffer in your signal chain addresses this issue. It's a low-noise buffer in a small, rugged housing; it can add up to +6dB of gain with the front-facing gain slider; it makes up for signal loss that can occur when combining effects with different impedance levels; it fine-tunes signal recovery with Hi and Lo cut switches; it has an extra output for a tuner, separate effects chain or amp, and can be set to receive either a buffered or unbuffered signal; it also features a convenient 9VDC power output jack which provides power for another pedal. The CAE Buffer is truly a mighty utility with a small footprint-an ideal addition to any effects rig or pedalboard!