Suhr Bella Reverb Head ...

38.990,-

Bella is a portable, American voiced, hand-wired, all-tube amplifier, designed to be the ideal grab-n-go amplifier and the ultimate platform for your pedalboard. Bella’s simple and easy to use controls (including Boost and 3-position Bright switch) make it a snap to tailor the amp to your favorite boost, overdrive, fuzz and distortion pedals; while the effects loop is the ideal place for all of your chorus, flange, delay, and reverb pedals. Bella is powered by a duet of 6L6GC power tubes that deliver either 22 or 44 Watts of Class A/B power and is available in a head or combo format, with or without reverb. 100% HANDWIRED Each Bella amplifier is meticulously hand wired, assembled, and tested in our Lake Elsinore, CA factory. SELECTABLE WATTAGE The Bella can be selected to run at either 44 or 22 watts. Choose 44 watts when you need the boldest tone with the most clean headroom. Choose 22 watts when you want the amp to break up sooner and at lower volumes. SWITCHABLE BOOST & BRIGHT TWO POSITION BOOST: This 2-position switch varies Bella’s input gain stage via the front panel or the footswitch (sold separately) jack located on the back of the amplifier. Engaging the boost provides +6dB of boost at the first gain stage. THREE POSITION BRIGHT: The bright switch has three selections available. In the down position: the Bright switch is out of the circuit. In the middle position: Bella introduces a modest amount of brightness that brings out the guitar’s upper frequencies. If you desire more organic chime, set Bella’s Bright switch to the up position. This position naturally opens up the top-end, allowing all of your guitar’s higher frequencies to shine through. TRANSPARENT EFFECTS LOOP Bella is equipped with a full-featured, all-tube series effects loop which performs equally well with pedals and line-level rack gear via the loop’s independent send and return controls. The effects loop was designed to be extremely clean and transparent, making it the ultimate effects platform. YOUR PEDALS HAVE NEVER SOUNDED SO GOOD Bella has been specially designed with your pedals in mind and it’s the ultimate, clean, pedal platform. It responds to virtually any pedal in a tone-full way and even the bright switch is friendly with most overdrives and distortions. OUTPUT: Switchable 44/22 Watts RMS PREAMP TUBES: 3x 12AX7 POWER TUBES: 2x 6L6GC REVERB: No EFFECTS LOOP: Tube driven, buffered, with independent send and return levels. SPEAKER: Sold Seperately FRONT PANEL: Input, Boost Switch (2-Position), Bright Switch (3-Position), Volume, Treble, Bass, and Presence, Standby/Wattage Selector Switch, and On/Off Power Switch BACK PANEL: Mains Input Inlet, Mains Fuse, H.T. Fuse, Speaker Impedance Selector: (2Ω, 4Ω, & 8Ω), 2-External Speaker Outputs, Effects Loop Return Level, Return and Send Jacks, Send Level, In/Out Switch and Boost Footswitch* Jack. *Footswitch sold separately. DIMENSIONS: 24” (W) x 9.90” (D) x 10.4” (H) WEIGHT: 35lbs

Suhr Corso Recording Amp ...

14.290,-

The Suhr Corso Recording Amplifier is the ideal studio companion. Corso is an all-tube no compromise variable wattage amplifier (up to 5 watts) that provides players with all the tone and character of a high powered amplifier in a compact, portable form factor - perfect for any recording studio application or bedroom practice session. Corso is packed with a number of features which give players incredible flexibility for carving out their ideal sound. With the on-board attenuator, Corso can be easily transformed from the most complex and detailed clean tones, to a wall of harmonically rich overdriven lead tones at any volume.  Equipped with unique a Line Out (post power section), the Corso is ready for the studio. The Corso’s Line Out offers the sound of the entire amplifier, not just the pre-amp section, so you can fully experience all of the Corso’s tone when you plug directly into your digital recording I/O interface for your next session. Should inspiration strike in the middle of the night, just turn the attenuator control fully counterclockwise and play without disturbing the neighbors, or your family.

Suhr Discovery Analog Delay ...

9.490,-

DISCOVERY Analog Delay The long-standing mission of Suhr has been to bring the simplicity and tone of analog circuitry to today’s guitarists. The Suhr Discovery Analog Delay is the new revolutionary pedal, designed by Kevin Suhr. The Discovery Analog Delay is the first of its kind, for Suhr and the world. Retaining the tone, vibe, and creative inspiration of iconic analog delay units, yet adding the versatility of the most modern and expandable delay pedals available today. Analog Evolved The warm, rich, unmistakable tone of an all-analog signal path with the control of the most modern, feature-filled pedals of today. Built on 4 reissued versions of the MN3005 Bucket Brigade analog delay chips, we sought out to achieve what no other analog delay on the market could, the ability to shape and control your delay in any way you wish. All savable to 127 presets. Modern Control With an intelligent Tap-Tempo that averages your last four taps, the Discovery Delay can help you really nail your tempo. 127 savable presets, allow you to save your favorite sounds and settings and recall them at the drop of a hat when using the Bypass and Tap-Tempo to instantly recall your presets. Shape Discovery’s Tone The Filter Section of the Discovery gives you utmost control to shape where your delay sits in the mix of your overall sound. With the Lo-Cut and Hi-Cut knobs, you can shave off bass or treble from your repeats. This will take you from thick, full delay fatness to the crisp, high-end of a dub-style echo. Modulation The Modulation control on Discovery allows you to capture the warble and flutter of a vintage analog delay, as well as give you the ability to get a modern space-aged chorus, all the way to classic Leslie-style speed shifts. You can even change the waveform of your modulation from triangle, sine and square waves. Ultimate Expression The sounds and possibilities can be limitless when you plug in an expression pedal to the Discovery. All knobs can be mapped to the expression pedal with a custom sweep for each one. A different mapping can be saved to each preset. From simply speeding up the delay time for those classic ‘tape-ramp’ tones, to getting an infinite regen/freeze sound to fill an expansive space. Expand With MIDI The Discovery has full MIDI capabilities from things as simple as switching between your saved presets, to fitting into a complex live MIDI set-up where you need full control of every parameter. Discovery has 5-pin in and out/thru can even send Program Changes (PCs) to your other pedals that accept MIDI. Whether you have a MIDI controller or you are switching with your DAW in the studio, the Discovery is the most simple solution in any situation. Features All-new revolutionary design Engineered on four re-issued versions of the renowned MN3005 bucket-brigade analog-delay chips 127 programmable presets Delay times of 40ms-1100ms, expandable to 17ms-2000ms & beyond with up/down & division buttons Subdivisions include quarter, dotted-eighth, eighth note triplet, eighth note and sixteenth note 7-segment display for BPM, milliseconds or preset number Classic analog delay warmth with the control to make it your own Studio quality tone & features Built-in smart Tap-Tempo giving you the ability to nail the tempo High & Lo Cut controls to shape the sound of your delay Modulation with speed & depth controls 3 modulation waveforms to choose from: Triangle, Sine and Square Fully programmable digital-control Use in ANY set-up with MIDI In & Out/Thru Every knob is mappable to an expression pedal Custom expression pedal mapping, savable to each preset Every parameter can be controlled by MIDI Can be used to send patch changes to your other MIDI devices Save all of your presets to a SysEx file for back-up or to share Switchable true-bypass or buffered-bypass Soft clipping limiter for infinite feedback and oscillations Kill dry mode for parallel effects loops Includes an 18V DC power supply Assembled in the USA

Suhr Hombre Combo 1x12 ...

27.390,-

Hombre, Suhr’s take on the classic Brownface tones that have inspired John Suhr since his early days as a guitarist. The intention was clear: create a modern take on these classic designs while preserving the vintage heritage. The purity of the signal path is part of Hombre’s beauty. It results in a playing experience that is incredibly dynamic and touch-sensitive. A simple turn of the volume and tone controls will put a shocking range of sound at your fingertips. Clean tones are classic, gorgeous and bell-like, but make no mistake, this amp is a dirty little combo. It wants to be pushed into sweet overdrive, conjuring tones from the 1970s era of Texas blues-rock. The onboard Dynamic Tube Bias tremolo imparts an unmistakably rich, sought after sound, that simply can’t be imitated. Hombre is driven by a ~18-watt 6V6 power section and features a lightweight cabinet loaded with a 12″ Celestion V-Type speaker. PURE SIGNAL PATH Hombre features a Normal and Bright channel with straightforward Volume and Tone controls. A simple, transparent signal path is something many players find alluring due to the purity of tone and superb dynamic range. Our goal was to maintain the vintage characteristics while simultaneously making some improvements to the design. Painstaking attention was given to the component layout and signal path to reduce noise. Hombre is equipped with custom made transformers that are wound on paper bobbins and made in the USA. DYNAMIC TUBE BIAS TREMOLO Bias Tremolo circuits are truly unique in that the effect is created by modulating the bias of the power tubes. As the power tube bias is lowered and raised, it imparts an unmistakably rich, sought after sound, that only a Tube Bias Tremolo can. There’s a distinct interaction that exists between the tremolo and the dynamics of the musician. The intensity of the tremolo can be influenced by how hard or soft the guitar is played. When the amp is pushed harder, or the musician plays harder, the tremolo effect is less noticeable, yet as the signal decays the effect becomes more apparent. This results in a stunning effect that lives and breathes with the music. VINTAGE CABINET DESIGN Hombre is a lightweight 1×12 combo that is the perfect grab-and-go companion for both gigs and studio sessions. The cabinet is a vintage design made from box jointed pine and features a floating baffle. After many hours of listening and testing, we chose a 12″ Celestion® V-Type speaker to accompany Hombre. VOLTAGE: 230V CONTROLS: Volume, Tone (Normal). Volume, Tone (Bright). Speed, Intensity (Tremolo) EFFECTS: Foot-switchable Tube-Biased Tremolo (Active In Normal & Bright Inputs) INPUTS: 2x Normal, 2x Bright WATTAGE: 18 watts SPEAKER OUTPUTS: 2 OPERATING IMPEDANCE: 8Ω (safe to operate at 4Ω or 16Ω - see user guide) CABINET MATERIAL: Box Jointed Pine TOLEX: Vintage Palomino Nubtex GRILL CLOTH: Tan/Brown Wheat SPEAKER: 12" Celestion® V-Type PREAMP TUBES: 3x 12AX7 POWER TUBES: 2x 6V6 RECTIFIER TUBE: 1x 5AR4 FOOT-SWITCH: Includes single button foot-switch for tremolo activation DIMENSIONS: 20.84" W x 18.1" H x 9.52" D WEIGHT: 33lbs  

Suhr Hombre Head ...

25.990,-

Hombre, Suhr’s take on the classic Brownface tones that have inspired John Suhr since his early days as a guitarist. The intention was clear: create a modern take on these classic designs while preserving the vintage heritage. The purity of the signal path is part of Hombre’s beauty. It results in a playing experience that is incredibly dynamic and touch-sensitive. A simple turn of the volume and tone controls will put a shocking range of sound at your fingertips. Clean tones are classic, gorgeous and bell-like, but make no mistake, this amp is a dirty little combo. It wants to be pushed into sweet overdrive, conjuring tones from the 1970s era of Texas blues-rock. The onboard Dynamic Tube Bias tremolo imparts an unmistakably rich, sought after sound, that simply can’t be imitated. Hombre is driven by a ~18-watt 6V6 power section. PURE SIGNAL PATH Hombre features a Normal and Bright channel with straightforward Volume and Tone controls. A simple, transparent signal path is something many players find alluring due to the purity of tone and superb dynamic range. Our goal was to maintain the vintage characteristics while simultaneously making some improvements to the design. Painstaking attention was given to the component layout and signal path to reduce noise. Hombre is equipped with custom made transformers that are wound on paper bobbins and made in the USA. DYNAMIC TUBE BIAS TREMOLO Bias Tremolo circuits are truly unique in that the effect is created by modulating the bias of the power tubes. As the power tube bias is lowered and raised, it imparts an unmistakably rich, sought after sound, that only a Tube Bias Tremolo can. There’s a distinct interaction that exists between the tremolo and the dynamics of the musician. The intensity of the tremolo can be influenced by how hard or soft the guitar is played. When the amp is pushed harder, or the musician plays harder, the tremolo effect is less noticeable, yet as the signal decays the effect becomes more apparent. This results in a stunning effect that lives and breathes with the music. VOLTAGE: 230V CONTROLS: Volume, Tone (Normal). Volume, Tone (Bright). Speed, Intensity (Tremolo) EFFECTS: Foot-switchable Tube-Biased Tremolo (Active In Normal & Bright Inputs) INPUTS: 2x Normal, 2x Bright WATTAGE: 18 watts SPEAKER OUTPUTS: 2 OPERATING IMPEDANCE: 8Ω (safe to operate at 4Ω or 16Ω - see user guide) CABINET MATERIAL: Box Jointed Pine TOLEX: Vintage Palomino Nubtex GRILL CLOTH: Tan/Brown Wheat SPEAKER: Speaker cabinet sold separately PREAMP TUBES: 3x 12AX7 POWER TUBES: 2x 6V6 RECTIFIER TUBE: 1x 5AR4 FOOT-SWITCH: Includes single button foot-switch for tremolo activation DIMENSIONS: 20.84" W x 9.23" H x 8.3" D WEIGHT: 18.6lbs

Suhr PT15 I.R. Signature 15W ...

45.990,-

Suhr PT-15 IR. Signature Edition. 15W Signature 3-Channel Tube Amp Head The PT15 I.R. is the world’s first truly hybrid amplifier, marrying classic tube circuitry with a reactive load and digital impulse response technology. With the PT15 I.R. we set out to combine the strengths of both analog and digital to create something new. The addition of a built-in Reactive Load and on-board impulse responses, make using a speaker cabinet optional for recording, or feeding front of house with a studio quality mic’ed up tone. Also included is a headphone output and auxiliary input to practice and jam along with your favorite tracks, wherever you are. The all-tube three channel design offers a plethora of American and British tones, powered by a new 6V6 driven power section. The dynamics, overdrive, saturation and harmonics that we crave as tonal purists, is all here. By adding channel assignable IRs, you now have unprecedented versatility and control over your tone, expanding your choices more than ever before. ALL-TUBE DESIGN For over 10 years Pete Thorn and John Suhr have been partners in tone. The PT15 is their latest creation, representing countless hours of refinement. At its heart, PT15 is an all-tube amplifier with a newly designed 6V6 power section. This new power section is incredibly tone-full, punchy, and dynamic. Headroom is something very important in a 15-watt amp, so the power section has been optimized to provide surprising levels of volume even for clean tones. The PT15 I.R. has no digital circuitry in the audio path, it’s 100% tube tone. Digital processing is only applied to the I.R. output. BUILT IN REACTIVE LOAD & I.R. TECHNOLOGY PT15 I.R. marries the best of what analog and digital have to offer. Equipped with our industry-standard reactive load, PT15 I.R. can be safely operated with no speaker connected. Impulse Responses are the most accurate way of replicating the sound of a speaker cabinet and microphone, virtually indistinguishable from the real thing. Use the line output to get huge mic’ed-up tone directly into your DAW, PA, or headphones. READY FOR THE STUDIO OR STAGE PT15 I.R. features channel-assignable impulse responses which are a breakthrough for live performance, letting you change the cabinet I.R. along with the channels of the amp. You can choose to play the amp silently on stage, or have a cabinet for stage volume while using the I.R. output to avoid the hassle, inconsistency, and bleed from mic’ing a cabinet. In the studio, you have the option of using the line output without an I.R. which gives you the flexibility to process impulse responses in your DAW. Pre-loaded with authentic Suhr cabinets. The PT15 I.R. comes loaded with 16 impulse responses of Suhr speaker cabinets. Six of the impulse responses are custom blends made by Pete Thorn himself. Because it is an open system, you can also load your own third-party IRs into the amplifier via USB. Each of the three amp channels can be assigned its own unique impulse response. This means, for example, you could assign an open back 2×12 to your clean channel and two different closed-back 4x12s for your lead channels. It’s like bringing an arsenal of cabinets to the gig. The best partner in the bedroom. …or any room, really. Simply connect your headphones to the front of the amp, select an IR, and practice silently with no speaker cabinet required. Connect any stereo 1/8″ audio source to the AUX IN connection and you’ll hear the IR processed signal along with your backing tracks through the headphones. CHANNELS: 3 OUTPUT: 15 watts FRONT PANEL: Input, Aux Input, Headphone Input, IR Level, (CH1) Bright Switch, Gain 1, Bass, Treble, Level 1, (CH 2/3): Bright 2/3 Switch, Gain 2, Gain 3, Bass, Middle, Treble, Level 2, Level 3, Channel Select Switch, I.R. Bank Select Button, I.R. Cab Select Button, I.R. LEDs, Power & Stand By switch BACK PANEL: H.T. Fuse, Mains Fuse, Mains Input, Reactive Load Parallel Output, Reactive Load Disconnected Output, Impedance Selector, FX Loop Send, FX Loop Return, Footswitch (TRS) jack, Balanced/Unbalanced Line Out, I.R. Filter Bypass Button, USB Jack TUBES: 2 x 6V6GT (Power Section), 5 x 12AX7 FX LOOP: Tube driven, buffered FOOTSWITCH: Included MAINS FUSE: T1.5A/250V (Slo-Blo) - 100/120VAC T.75A/250V (Slo-Blo) - 230/240VAC H.T. FUSE: F.5A/250V (Fast-Blo) I.R. FORMAT: WAV, Mono, 24bit, 48kHz, 20.5 ms (I.R.s greater than 20.5 ms will be truncated to 20.5 ms) I.R. OUTPUT LATENCY: 1.2ms DIMENSIONS: 20.5" (W) x 8.25” (D) x 9.25” (H) WEIGHT: 24.7 lbs

Suhr PT15 Signature 15W ...

37.790,-

Suhr PT-15. Signature 15W, 3-Channel Tube Amp Head. The all-tube three channel design offers a plethora of American and British tones, powered by a new 6V6 driven power section. The dynamics, overdrive, saturation and harmonics that we crave as tonal purists, is all here. The same amazing all-tube circuit as the PT15 I.R. but without the built-in reactive load, impulse responses, or headphone output. ALL-TUBE DESIGN For over 10 years Pete Thorn and John Suhr have been partners in tone. The PT15 is their latest creation, representing countless hours of refinement. At its heart, PT15 is an all-tube amplifier with a newly designed 6V6 power section. This new power section is incredibly tone-full, punchy, and dynamic. Headroom is something very important in a 15-watt amp, so the power section has been optimized to provide surprising levels of volume even for clean tones. CHANNELS: 3 OUTPUT: 15 watts FRONT PANEL: Input, (CH1) Bright Switch, Gain 1, Bass, Treble, Level 1, (CH 2/3): Bright 2/3 Switch, Gain 2, Gain 3, Bass, Middle, Treble, Level 2, Level 3, Channel Select Switch, Power & Stand By switch BACK PANEL: H.T. Fuse, Mains Fuse, Mains Input, 1/4" Speaker Outputs, Impedance Selector, FX Loop Send, FX Loop Return, Footswitch (TRS) jack TUBES: 2 x 6V6GT (Power Section), 5 x 12AX7 FX LOOP: Tube driven, buffered FOOTSWITCH: Included MAINS FUSE: T1.5A/250V (Slo-Blo) - 100/120VAC T.75A/250V (Slo-Blo) - 230/240VAC H.T. FUSE: F.5A/250V (Fast-Blo) DIMENSIONS: 20.5" (W) x 8.25” (D) x 9.25” (H) WEIGHT: 23.7 lbs

Suhr Riot Distortion Pedal

3.790,-

SUHR RIOT DISTORTION PEDAL Riot is a versatile high-gain distortion pedal with the sonic characteristics and touch sensitivity of a high quality 100 watt tube amplifier. OUR ORIGINAL DISTORTION Riot will transform a clean amp into an authoritative rock tone that inspires all of your favorite riffs. CONTROLS DIST: Adjusts the amount of gain added to your tone, taking you from classic crunch to high-gain heaven. LEVEL: Adjusts the output of the pedal. Riot provides enough level to push the front end of any tube amp into natural overdrive. TONE: Shapes the overall tonal response of the pedal, from smooth and warm to cutting lead tones. VOICING SWITCH Left: Produces a natural, organic tone that responds dynamically to your guitars volume control. Middle: Puts you into high gain territory with a solid midrange, with a tight bottom end. Right: Produces a vintage high gain response, with excellent definition. UNIQUE FEATURES True Bypass: Riot is true bypass via a relay. This function allows for the remote switching, and the battery monitor feature. The relay produces less popping when switching the pedal on and off. FX Link: The FX Link connector allows the pedal’s switching function to be controlled from an external switch, pedal board, loop switcher, or any other custom interface. FX Link also provides the ability to power up in the On/Off state. Low Battery Monitor: Riot incorporates a unique battery monitor that alerts the user to low battery conditions. In addition, the battery monitor will automatically switch the pedal to True Bypass if the battery voltage is too low for the circuitry to correctly operate.

Suhr Riot Galactic LTD. ...

3.990,-

Suhr Riot Galactic LTD. Distortion Pedal This is an Exclusive Run of Suhr's most popular pedal! With only 150 units produced worldwide in a celestial Dark Matter Metallic (flip flops from blue to purple) powder coat, this is the Riot Galactic. Riot is a versatile high-gain distortion pedal with the sonic characteristics and touch sensitivity of a high quality 100 watt tube amplifier. 

Suhr Riot Reloaded Distortion ...

3.790,-

SUHR RIOT RELOADED DISTORTION PEDAL In 2009, we shipped our very first Riot distortion pedal. Riot became an overnight success, offering players the ability to transform a clean amp into a versatile Classic Rock tone machine. Riot Reloaded is the result of countless hours of listening, testing, and tweaking our original distortion circuit to create a pedal that is amp-like, aggressive, in your face, and features more gain (30% more than our original Riot). An excellent companion to the original Riot, Riot Reloaded is a versatile distortion pedal that delivers a broad spectrum of Hi-Gain tones, with an amp-like feel, in a compact stompbox. 30% MORE GAIN With 30% more gain than the original, Riot Reloaded is the ideal choice for players seeking Hi-Gain Rock, Metal, and drop tuning style tones. HIGH GAIN AMP-LIKE PERFORMANCE AMP-LIKE PERFORMANCE Riot Reloaded responds dynamically to every nuance of your playing, just like the overdrive channel of a modded amplifier. With a simple twist of your volume knob, you can easily morph from mild chunk to full on metal assault. GAIN TO SPARE Riot Reloaded offers over 30% more gain than our original Riot. Our engineers balanced the dual gain stages to increase saturation and upper harmonics, resulting in improved midrange articulation, more sustain, and a tighter three-dimensional sound. YOUR TONE, YOUR CHOICE TONE SHAPING The tone control was modified to emphasize upper mid frequencies for a sweeter, more cutting tone, without sounding harsh or fatiguing. VOICE SWITCH The versatile three position voicing switch provides Classic, Modern (Full bodied), and Scooped EQ settings. ADDITIONAL FEATURES True Bypass: Riot is true bypass via a relay. This function allows for the remote switching, and the battery monitor feature. The relay produces less popping when switching the pedal on and off. FX Link: The FX Link connector allows the pedal’s switching function to be controlled from an external switch, pedal board, loop switcher, or any other custom interface. FX Link also provides the ability to power up in the On/Off state. Low Battery Monitor: Riot incorporates a unique battery monitor that alerts the user to low battery conditions. In addition, the battery monitor will automatically switch the pedal to True Bypass if the battery voltage is too low for the circuitry to correctly operate. INPUT IMPEDANCE: 1M ohm OUTPUT IMPEDANCE: 600 ohm POWER CONNECTOR: 9Vdc, center negative, 2.1mm x 5.5mm OPERATING VOLTAGE: 4V to 18V (nominal 9V) MAXIMUM VOLTAGE: 20Vdc REVERSE BATTERY PROTECTION: Yes OVER VOLTAGE PROTECTION: Yes CURRENT CONSUMPTION: 8mA ESTIMATED BATTERY LIFE: 75 – 100 hours of continuous use DIMENSIONS: 2.5”(W) x 4.5”(D) x 1.25”(H) WEIGHT: 0.75lb FX LINK CONNECTOR: 1/8" Mono FX LINK MAX VOLTAGE: 3.3Vdc SHIELD → TIP: Activate Pedal ROHS COMPLIANT: Yes

Suhr Rufus Fuzz Pedal

3.790,-

SUHR RUFUS FUZZ PEDAL Rufus is a unique fuzz pedal designed to offer a wealth of fuzz tone effects with the dynamics and tactile response of a tube amplifier. Whether your tastes are for the historic tones created at The Fillmore East back in ‘69, or you crave the more aggressive, mid-scoped characteristics of the Grunge-era, Rufus has you covered, and then some. MX(X) TECHNOLOGY Switch between Rufus’ two modes (normal and fat) in mid performance by pressing and holding the footswitch. BEYOND TRADITIONAL Designed for ultimate versatility, Rufus is equipped with a full featured 3-Band EQ that gives you the ability to easily shape Rufus’ tone without compromising the sound of your guitar or bass rig. Did we just say bass? Yes we did. Rufus is an equal opportunity fuzz pedal that plays well with guitars and basses – no need to worry about losing your bottom-end here. Rufus employs True Bypass switching which totally removes the effect from the signal chain in our dedication to preserve your tone. ONE PEDAL, TWO MODES Created to enhance your overall playing experience, we developed Multi-Function Technology mf(x). mf(x) is a proprietary foot switch technology that enables you to seamlessly select between Rufus’ two distinct user modes, Normal and Fat, during a performance just by holding down it’s foot switch. Would you like to default to one mode in particular the next time you turn on Rufus? Not a problem; mf(x) has built in memory that remembers your last mode choice. ADDITIONAL FEATURES True Bypass: Rufus is true bypass via a relay. This function allows for the remote switching, and the battery monitor feature. The relay produces less popping when switching the pedal on and off. FX Link: The FX Link connector allows the pedal’s switching function to be controlled from an external switch, pedal board, loop switcher, or any other custom interface. FX Link also provides the ability to power up in the On/Off state. Low Battery Monitor: Rufus incorporates a unique battery monitor that alerts the user to low battery conditions. In addition, the battery monitor will automatically switch the pedal to True Bypass if the battery voltage is too low for the circuitry to correctly operate. INPUT IMPEDANCE: 5K ohm OUTPUT IMPEDANCE: 10K ohm POWER CONNECTOR: 9Vdc, center negative, 2.1mm x 5.5mm OPERATING VOLTAGE: 9Vdc MAXIMUM VOLTAGE: 18Vdc REVERSE BATTERY PROTECTION: Yes OVER VOLTAGE PROTECTION: Yes CURRENT CONSUMPTION: 9mA ESTIMATED BATTERY LIFE: Approximately 60 hours of continuous use DIMENSIONS: 2.5”(W) x 4.5”(D) x 1.25”(H) WEIGHT: 0.75lb FX LINK CONNECTOR: 1/8" Stereo FX LINK MAX VOLTAGE: 3.3Vdc SHIELD → TIP: Activate Green (normal) Mode SHIELD → RING: Activate Red (fat) Mode ROHS COMPLIANT: Yes

Suhr Rufus Reloaded Fuzz ...

3.790,-

SUHR RUFUS RELOADED FUZZ PEDAL Rufus Reloaded is a unique pedal that offers a vast array of fuzz tones. With the Re|Loaded edition we’ve added an extremely dynamic and tactile octave-up effect. We focused our development on creating a powerful, easy to play octave-up, that responds evenly across all of your instrument’s pickup selections and the entire fingerboard – effortlessly delivering the iconic “Band of Gypsys” tone at your fingertips. MF(X) TECHNOLOGY Switch between Rufus Reloaded’s two modes (normal and octave up) in mid performance by pressing and holding the footswitch. BEYOND TRADITIONAL Designed for ultimate versatility, Rufus is equipped with a full featured 3-Band EQ that gives you the ability to easily shape Rufus’ tone without compromising the sound of your guitar or bass rig. Did we just say bass? Yes we did. Rufus is an equal opportunity fuzz pedal that plays well with guitars and basses – no need to worry about losing your bottom-end here. For the Reloaded version, we’ve added a classic octave up mode. We set out to make this effect easier to play than traditional octave fuzzes, and be present across the entire fretboard. ONE PEDAL, TWO MODES Created to enhance your overall playing experience, we developed Multi-Function Technology mf(x). mf(x) is a proprietary foot switch technology that enables you to seamlessly select between Rufus’ two distinct user modes, Normal and Octave, during a performance just by holding down it’s foot switch. Would you like to default to one mode in particular the next time you turn on Rufus? Not a problem; mf(x)has built in memory that remembers your last mode choice. ADDITIONAL FEATURES True Bypass: Rufus Reloaded is true bypass via a relay. This function allows for the remote switching, and the battery monitor feature. The relay produces less popping when switching the pedal on and off. FX Link: The FX Link connector allows the pedal’s switching function to be controlled from an external switch, pedal board, loop switcher, or any other custom interface. FX Link also provides the ability to power up in the On/Off state. Low Battery Monitor: Rufus Reloaded incorporates a unique battery monitor that alerts the user to low battery conditions. In addition, the battery monitor will automatically switch the pedal to True Bypass if the battery voltage is too low for the circuitry to correctly operate.

Suhr Shiba Drive Overdrive ...

3.795,-

SUHR SHIBA DRIVE PEDAL Shiba Drive™ is a smooth sounding overdrive pedal that provides players with a wide variety of fat rhythm and warm lead tones. Shiba Drive is very popular among players seeking an overdrive pedal that can be used in conjunction with both their amplifier’s clean and overdrive channels. CONTROLS Shiba Drive™ features an easy to tweak layout which includes Drive, Level, Tone, and a Smooth switch. Drive: Controls the amount of Drive from the circuit. This will take you from a bluesy crunch to a sustained, compressed overdrive. Level: Controls the output level of the pedal. Shiba provides enough level to push the front end of any tube amp into natural clipping, or adds sustain to an already overdriven amp. Tone: Shapes the the overall tonal response of the pedal – from warm and smooth to bright and cutting. SMOOTH SWITCH Left: Activates as a mild high-end roll off. Effective for warming up guitars with single-coil pickups. Middle: Voiced to produce a natural, open sounding overdrive. Right: A more pronounced high-end roll off. Excellent for chunky rhythms and violin-like lead tones. Note: The modes have less effect at lower gain and tone settings. ADDITIONAL FEATURES True Bypass: Shiba is true bypass via a relay. This function allows for the remote switching, and the battery monitor feature. The relay produces less popping when switching the pedal on and off. FX Link: The FX Link connector allows the pedal’s switching function to be controlled from an external switch, pedal board, loop switcher, or any other custom interface. FX Link also provides the ability to power up in the On/Off state. Low Battery Monitor: A unique battery monitor alerts the user to low battery conditions. In addition, the battery monitor will automatically switch the pedal to True Bypass if the battery voltage is too low for the circuitry to correctly operate. OUTPUT IMPEDANCE: 600 ohm POWER CONNECTOR: 9Vdc, center negative, 2.1mm x 5.5mm OPERATING VOLTAGE: 4V to 18V (nominal 9V) MAXIMUM VOLTAGE: 20Vdc REVERSE BATTERY PROTECTION: Yes OVER VOLTAGE PROTECTION: Yes CURRENT CONSUMPTION: 8mA ESTIMATED BATTERY LIFE: 75 – 100 hours of continuous use DIMENSIONS: 2.5”(W) x 4.5”(D) x 1.25”(H) WEIGHT: 0.75lb FX LINK CONNECTOR: 1/8" Mono FX LINK MAX VOLTAGE: 3.3Vdc SHIELD → TIP: Activate Pedal ROHS COMPLIANT: Yes

Suhr Shiba Drive Reloaded ...

3.795,-

SUHR SHIBA DRIVE PEDAL In July of 2009, we shipped our very first Shiba Drive pedal. Shiba was designed to provide players with a variety of fat rhythm and warm singing lead tones. The Shiba Drive gained great popularity among players seeking an overdrive pedal that could be used in conjunction with their amplifier’s clean or overdrive channels for added flexibility. Shiba Reloaded is the ideal choice for players seeking classic Blues, Jazz, and Rock style tones. TIGHTER BASS. MORE GAIN. Shiba Drive Reloaded is the result of countless hours of listening, testing, and tweaking our original overdrive circuit to create a pedal that is more amp-like, has a tighter low-end, focused mids, and features more gain (50% more than our original Shiba). SMOOTH AMP-LIKE PERFORMANCE AMP-LIKE PERFORMANCE Designed to work equally well with single coil and humbucking instruments, the Shiba Reloaded responds dynamically to every nuance of your playing, just like the overdrive channel of a tube amplifier. With a simple twist of your volume knob, you can easily morph from pushed clean to full-on Classic Rock style tones. GAIN TO SPARE The Shiba Drive Reloaded offers over 50% more gain than our original Shiba Drive. Our engineers fine-tuned its gain stage, increased saturation and upper harmonics, which resulted in improved midrange articulation and more sustain, allowing your notes to sing without sacrificing low-end definition. SMOOTH SWITCH We redesigned Shiba’s Smooth switch to be more apparent offering flexibility, giving you the ability to fine tune your sound. Whether you prefer warm violin-like solos or an open and defined full-bodied rhythm tone, Shiba Drive Reloaded is your ideal overdrive pedal for a variety of playing styles. An excellent companion to the original Shiba Drive, Shiba Drive Reloaded is a versatile overdrive pedal that delivers a broad range of pushed/overdriven tones, with an amp-like feel, all within a compact stompbox. ADDITIONAL FEATURES True Bypass: Shiba Drive Reloaded is true bypass via a relay. This function allows for the remote switching, and the battery monitor feature. The relay produces less popping when switching the pedal on and off. FX Link: The FX Link connector allows the pedal’s switching function to be controlled from an external switch, pedal board, loop switcher, or any other custom interface. FX Link also provides the ability to power up in the On/Off state. Low Battery Monitor: Shiba Drive Reloaded incorporates a unique battery monitor that alerts the user to low battery conditions. In addition, the battery monitor will automatically switch the pedal to True Bypass if the battery voltage is too low for the circuitry to correctly operate. OUTPUT IMPEDANCE: 600 ohm POWER CONNECTOR: 9Vdc, center negative, 2.1mm x 5.5mm OPERATING VOLTAGE: 4V to 18V (nominal 9V) MAXIMUM VOLTAGE: 20Vdc REVERSE BATTERY PROTECTION: Yes OVER VOLTAGE PROTECTION: Yes CURRENT CONSUMPTION: 8mA ESTIMATED BATTERY LIFE: 75 – 100 hours of continuous use DIMENSIONS: 2.5”(W) x 4.5”(D) x 1.25”(H) WEIGHT: 0.75lb FX LINK CONNECTOR: 1/8" Mono FX LINK MAX VOLTAGE: 3.3Vdc SHIELD → TIP: Activate Pedal ROHS COMPLIANT: Yes

T-Rex Creamer Reverb pedal

1.250,-

T-Rex Creamer 3 reverb i samme pedal   Stort och varmt eller bara en liten gnutta för att ge din ton lite rymd. Det spelar ingen roll hur du vill använda Creamern, den passar in och lägger sig där du vill ha den. En lätt rattad reverbpedal som erbjuder 3 sorters reverb i samma pedal. Room Spring och Hall So, you finally got your rig dialed in and it sounds fantastic, but sometimes you feel like adding a bit of depth or airy-ness to it. You want to fill in the holes in your playing, add some ambience or you maybe just really like those dreamy, special sounds that seem to take on a life of their own. HOWEVER, you don´t want to be lost in sub-menus or unfamiliar parameters, your pedal board is pretty much packed with all your precious goodies and you don´t want to ruin that tone you finally nailed. We have designed the Creamer reverb to be dead simple to operate, but with just enough room for tweaking, so you don´t feel limited in your search for the sonic equivalent of Grand Canyon or that small room we frequently visit every day. ANALOG TECHNOLOGY   The Creamer never digitizes your beloved guitar signal. It simply mixes in the reverb sound with the analog dry signal, so your tone is not tampered with in any way. It features three different reverb algorithms, which can be further adjusted to your liking with the knobs – set them fairly low and you can get the classic, more subtle reverbs, but there are lots of spaciousness available once you start to dime the knobs! The Creamer Reverb is your no nonsense, easy-to-use, great sounding reverb pedal that should enhance your playing in such a way, that you never really turn it off – things just sound better with a bit of cream on top! Information Typ Reverb x 3 Reglage 1 Reverb Reglage 2 Decay Reglage 3 Tone Reglage 4 Hall/Spring/Room In/Ut Tele/Tele Volt/mA 70mA Mått 60 x 50 x 115mm Vikt 0,250kg  

Viser 1666 til 1680 (av 2220 produkter)