Suhr Bella Head ...

33.390,-

Bella is a portable, American voiced, hand-wired, all-tube amplifier, designed to be the ideal grab-n-go amplifier and the ultimate platform for your pedalboard. Bella’s simple and easy to use controls (including Boost and 3-position Bright switch) make it a snap to tailor the amp to your favorite boost, overdrive, fuzz and distortion pedals; while the effects loop is the ideal place for all of your chorus, flange, delay, and reverb pedals. Bella is powered by a duet of 6L6GC power tubes that deliver either 22 or 44 Watts of Class A/B power and is available in a head or combo format, with or without reverb. 100% HANDWIRED Each Bella amplifier is meticulously hand wired, assembled, and tested in our Lake Elsinore, CA factory. SELECTABLE WATTAGE The Bella can be selected to run at either 44 or 22 watts. Choose 44 watts when you need the boldest tone with the most clean headroom. Choose 22 watts when you want the amp to break up sooner and at lower volumes. SWITCHABLE BOOST & BRIGHT TWO POSITION BOOST: This 2-position switch varies Bella’s input gain stage via the front panel or the footswitch (sold separately) jack located on the back of the amplifier. Engaging the boost provides +6dB of boost at the first gain stage. THREE POSITION BRIGHT: The bright switch has three selections available. In the down position: the Bright switch is out of the circuit. In the middle position: Bella introduces a modest amount of brightness that brings out the guitar’s upper frequencies. If you desire more organic chime, set Bella’s Bright switch to the up position. This position naturally opens up the top-end, allowing all of your guitar’s higher frequencies to shine through. TRANSPARENT EFFECTS LOOP Bella is equipped with a full-featured, all-tube series effects loop which performs equally well with pedals and line-level rack gear via the loop’s independent send and return controls. The effects loop was designed to be extremely clean and transparent, making it the ultimate effects platform. YOUR PEDALS HAVE NEVER SOUNDED SO GOOD Bella has been specially designed with your pedals in mind and it’s the ultimate, clean, pedal platform. It responds to virtually any pedal in a tone-full way and even the bright switch is friendly with most overdrives and distortions. OUTPUT: Switchable 44/22 Watts RMS PREAMP TUBES: 3x 12AX7 POWER TUBES: 2x 6L6GC REVERB: No EFFECTS LOOP: Tube driven, buffered, with independent send and return levels. SPEAKER: Sold Seperately FRONT PANEL: Input, Boost Switch (2-Position), Bright Switch (3-Position), Volume, Treble, Bass, and Presence, Standby/Wattage Selector Switch, and On/Off Power Switch BACK PANEL: Mains Input Inlet, Mains Fuse, H.T. Fuse, Speaker Impedance Selector: (2Ω, 4Ω, & 8Ω), 2-External Speaker Outputs, Effects Loop Return Level, Return and Send Jacks, Send Level, In/Out Switch and Boost Footswitch* Jack. *Footswitch sold separately. DIMENSIONS: 24” (W) x 9.90” (D) x 10.4” (H) WEIGHT: 35lbs

Suhr Bella Reverb Head ...

38.990,-

Bella is a portable, American voiced, hand-wired, all-tube amplifier, designed to be the ideal grab-n-go amplifier and the ultimate platform for your pedalboard. Bella’s simple and easy to use controls (including Boost and 3-position Bright switch) make it a snap to tailor the amp to your favorite boost, overdrive, fuzz and distortion pedals; while the effects loop is the ideal place for all of your chorus, flange, delay, and reverb pedals. Bella is powered by a duet of 6L6GC power tubes that deliver either 22 or 44 Watts of Class A/B power and is available in a head or combo format, with or without reverb. 100% HANDWIRED Each Bella amplifier is meticulously hand wired, assembled, and tested in our Lake Elsinore, CA factory. SELECTABLE WATTAGE The Bella can be selected to run at either 44 or 22 watts. Choose 44 watts when you need the boldest tone with the most clean headroom. Choose 22 watts when you want the amp to break up sooner and at lower volumes. SWITCHABLE BOOST & BRIGHT TWO POSITION BOOST: This 2-position switch varies Bella’s input gain stage via the front panel or the footswitch (sold separately) jack located on the back of the amplifier. Engaging the boost provides +6dB of boost at the first gain stage. THREE POSITION BRIGHT: The bright switch has three selections available. In the down position: the Bright switch is out of the circuit. In the middle position: Bella introduces a modest amount of brightness that brings out the guitar’s upper frequencies. If you desire more organic chime, set Bella’s Bright switch to the up position. This position naturally opens up the top-end, allowing all of your guitar’s higher frequencies to shine through. TRANSPARENT EFFECTS LOOP Bella is equipped with a full-featured, all-tube series effects loop which performs equally well with pedals and line-level rack gear via the loop’s independent send and return controls. The effects loop was designed to be extremely clean and transparent, making it the ultimate effects platform. YOUR PEDALS HAVE NEVER SOUNDED SO GOOD Bella has been specially designed with your pedals in mind and it’s the ultimate, clean, pedal platform. It responds to virtually any pedal in a tone-full way and even the bright switch is friendly with most overdrives and distortions. OUTPUT: Switchable 44/22 Watts RMS PREAMP TUBES: 3x 12AX7 POWER TUBES: 2x 6L6GC REVERB: No EFFECTS LOOP: Tube driven, buffered, with independent send and return levels. SPEAKER: Sold Seperately FRONT PANEL: Input, Boost Switch (2-Position), Bright Switch (3-Position), Volume, Treble, Bass, and Presence, Standby/Wattage Selector Switch, and On/Off Power Switch BACK PANEL: Mains Input Inlet, Mains Fuse, H.T. Fuse, Speaker Impedance Selector: (2Ω, 4Ω, & 8Ω), 2-External Speaker Outputs, Effects Loop Return Level, Return and Send Jacks, Send Level, In/Out Switch and Boost Footswitch* Jack. *Footswitch sold separately. DIMENSIONS: 24” (W) x 9.90” (D) x 10.4” (H) WEIGHT: 35lbs

Suhr Hombre Head ...

25.990,-

Hombre, Suhr’s take on the classic Brownface tones that have inspired John Suhr since his early days as a guitarist. The intention was clear: create a modern take on these classic designs while preserving the vintage heritage. The purity of the signal path is part of Hombre’s beauty. It results in a playing experience that is incredibly dynamic and touch-sensitive. A simple turn of the volume and tone controls will put a shocking range of sound at your fingertips. Clean tones are classic, gorgeous and bell-like, but make no mistake, this amp is a dirty little combo. It wants to be pushed into sweet overdrive, conjuring tones from the 1970s era of Texas blues-rock. The onboard Dynamic Tube Bias tremolo imparts an unmistakably rich, sought after sound, that simply can’t be imitated. Hombre is driven by a ~18-watt 6V6 power section. PURE SIGNAL PATH Hombre features a Normal and Bright channel with straightforward Volume and Tone controls. A simple, transparent signal path is something many players find alluring due to the purity of tone and superb dynamic range. Our goal was to maintain the vintage characteristics while simultaneously making some improvements to the design. Painstaking attention was given to the component layout and signal path to reduce noise. Hombre is equipped with custom made transformers that are wound on paper bobbins and made in the USA. DYNAMIC TUBE BIAS TREMOLO Bias Tremolo circuits are truly unique in that the effect is created by modulating the bias of the power tubes. As the power tube bias is lowered and raised, it imparts an unmistakably rich, sought after sound, that only a Tube Bias Tremolo can. There’s a distinct interaction that exists between the tremolo and the dynamics of the musician. The intensity of the tremolo can be influenced by how hard or soft the guitar is played. When the amp is pushed harder, or the musician plays harder, the tremolo effect is less noticeable, yet as the signal decays the effect becomes more apparent. This results in a stunning effect that lives and breathes with the music. VOLTAGE: 230V CONTROLS: Volume, Tone (Normal). Volume, Tone (Bright). Speed, Intensity (Tremolo) EFFECTS: Foot-switchable Tube-Biased Tremolo (Active In Normal & Bright Inputs) INPUTS: 2x Normal, 2x Bright WATTAGE: 18 watts SPEAKER OUTPUTS: 2 OPERATING IMPEDANCE: 8Ω (safe to operate at 4Ω or 16Ω - see user guide) CABINET MATERIAL: Box Jointed Pine TOLEX: Vintage Palomino Nubtex GRILL CLOTH: Tan/Brown Wheat SPEAKER: Speaker cabinet sold separately PREAMP TUBES: 3x 12AX7 POWER TUBES: 2x 6V6 RECTIFIER TUBE: 1x 5AR4 FOOT-SWITCH: Includes single button foot-switch for tremolo activation DIMENSIONS: 20.84" W x 9.23" H x 8.3" D WEIGHT: 18.6lbs

Suhr PT15 I.R. Signature 15W ...

45.990,-

Suhr PT-15 IR. Signature Edition. 15W Signature 3-Channel Tube Amp Head The PT15 I.R. is the world’s first truly hybrid amplifier, marrying classic tube circuitry with a reactive load and digital impulse response technology. With the PT15 I.R. we set out to combine the strengths of both analog and digital to create something new. The addition of a built-in Reactive Load and on-board impulse responses, make using a speaker cabinet optional for recording, or feeding front of house with a studio quality mic’ed up tone. Also included is a headphone output and auxiliary input to practice and jam along with your favorite tracks, wherever you are. The all-tube three channel design offers a plethora of American and British tones, powered by a new 6V6 driven power section. The dynamics, overdrive, saturation and harmonics that we crave as tonal purists, is all here. By adding channel assignable IRs, you now have unprecedented versatility and control over your tone, expanding your choices more than ever before. ALL-TUBE DESIGN For over 10 years Pete Thorn and John Suhr have been partners in tone. The PT15 is their latest creation, representing countless hours of refinement. At its heart, PT15 is an all-tube amplifier with a newly designed 6V6 power section. This new power section is incredibly tone-full, punchy, and dynamic. Headroom is something very important in a 15-watt amp, so the power section has been optimized to provide surprising levels of volume even for clean tones. The PT15 I.R. has no digital circuitry in the audio path, it’s 100% tube tone. Digital processing is only applied to the I.R. output. BUILT IN REACTIVE LOAD & I.R. TECHNOLOGY PT15 I.R. marries the best of what analog and digital have to offer. Equipped with our industry-standard reactive load, PT15 I.R. can be safely operated with no speaker connected. Impulse Responses are the most accurate way of replicating the sound of a speaker cabinet and microphone, virtually indistinguishable from the real thing. Use the line output to get huge mic’ed-up tone directly into your DAW, PA, or headphones. READY FOR THE STUDIO OR STAGE PT15 I.R. features channel-assignable impulse responses which are a breakthrough for live performance, letting you change the cabinet I.R. along with the channels of the amp. You can choose to play the amp silently on stage, or have a cabinet for stage volume while using the I.R. output to avoid the hassle, inconsistency, and bleed from mic’ing a cabinet. In the studio, you have the option of using the line output without an I.R. which gives you the flexibility to process impulse responses in your DAW. Pre-loaded with authentic Suhr cabinets. The PT15 I.R. comes loaded with 16 impulse responses of Suhr speaker cabinets. Six of the impulse responses are custom blends made by Pete Thorn himself. Because it is an open system, you can also load your own third-party IRs into the amplifier via USB. Each of the three amp channels can be assigned its own unique impulse response. This means, for example, you could assign an open back 2×12 to your clean channel and two different closed-back 4x12s for your lead channels. It’s like bringing an arsenal of cabinets to the gig. The best partner in the bedroom. …or any room, really. Simply connect your headphones to the front of the amp, select an IR, and practice silently with no speaker cabinet required. Connect any stereo 1/8″ audio source to the AUX IN connection and you’ll hear the IR processed signal along with your backing tracks through the headphones. CHANNELS: 3 OUTPUT: 15 watts FRONT PANEL: Input, Aux Input, Headphone Input, IR Level, (CH1) Bright Switch, Gain 1, Bass, Treble, Level 1, (CH 2/3): Bright 2/3 Switch, Gain 2, Gain 3, Bass, Middle, Treble, Level 2, Level 3, Channel Select Switch, I.R. Bank Select Button, I.R. Cab Select Button, I.R. LEDs, Power & Stand By switch BACK PANEL: H.T. Fuse, Mains Fuse, Mains Input, Reactive Load Parallel Output, Reactive Load Disconnected Output, Impedance Selector, FX Loop Send, FX Loop Return, Footswitch (TRS) jack, Balanced/Unbalanced Line Out, I.R. Filter Bypass Button, USB Jack TUBES: 2 x 6V6GT (Power Section), 5 x 12AX7 FX LOOP: Tube driven, buffered FOOTSWITCH: Included MAINS FUSE: T1.5A/250V (Slo-Blo) - 100/120VAC T.75A/250V (Slo-Blo) - 230/240VAC H.T. FUSE: F.5A/250V (Fast-Blo) I.R. FORMAT: WAV, Mono, 24bit, 48kHz, 20.5 ms (I.R.s greater than 20.5 ms will be truncated to 20.5 ms) I.R. OUTPUT LATENCY: 1.2ms DIMENSIONS: 20.5" (W) x 8.25” (D) x 9.25” (H) WEIGHT: 24.7 lbs

Suhr PT15 Signature 15W ...

37.790,-

Suhr PT-15. Signature 15W, 3-Channel Tube Amp Head. The all-tube three channel design offers a plethora of American and British tones, powered by a new 6V6 driven power section. The dynamics, overdrive, saturation and harmonics that we crave as tonal purists, is all here. The same amazing all-tube circuit as the PT15 I.R. but without the built-in reactive load, impulse responses, or headphone output. ALL-TUBE DESIGN For over 10 years Pete Thorn and John Suhr have been partners in tone. The PT15 is their latest creation, representing countless hours of refinement. At its heart, PT15 is an all-tube amplifier with a newly designed 6V6 power section. This new power section is incredibly tone-full, punchy, and dynamic. Headroom is something very important in a 15-watt amp, so the power section has been optimized to provide surprising levels of volume even for clean tones. CHANNELS: 3 OUTPUT: 15 watts FRONT PANEL: Input, (CH1) Bright Switch, Gain 1, Bass, Treble, Level 1, (CH 2/3): Bright 2/3 Switch, Gain 2, Gain 3, Bass, Middle, Treble, Level 2, Level 3, Channel Select Switch, Power & Stand By switch BACK PANEL: H.T. Fuse, Mains Fuse, Mains Input, 1/4" Speaker Outputs, Impedance Selector, FX Loop Send, FX Loop Return, Footswitch (TRS) jack TUBES: 2 x 6V6GT (Power Section), 5 x 12AX7 FX LOOP: Tube driven, buffered FOOTSWITCH: Included MAINS FUSE: T1.5A/250V (Slo-Blo) - 100/120VAC T.75A/250V (Slo-Blo) - 230/240VAC H.T. FUSE: F.5A/250V (Fast-Blo) DIMENSIONS: 20.5" (W) x 8.25” (D) x 9.25” (H) WEIGHT: 23.7 lbs